6254-FN聚酰亞胺薄膜F46膠帶

一、產品簡介：
     6254-FN聚酰亞胺薄膜F46膠帶是由6051-FN型聚酰亞胺薄膜單面或雙面涂以F46膠經干燥分切而成的膠帶（以下簡稱膠帶）。該膠帶使用于做電工導線繞包絕緣材料，在350℃—380℃溫度下0.5min 熔融成型。執行標準：KAPTON*FN型絕緣膜。

二、技術參數：

  1.外觀：膠帶應干爽、平整、無氣泡、無雜質 

  2.尺寸： 

     1）長度：膠帶長度及接頭數根據用戶要求，滿足其需要。 

     2）寬度：膠帶的寬度及允許偏差為10mm±0.5mm、15mm±0.5mm。根據用戶需求可提供其他寬度規格的膠帶。 

     3）膠帶的標稱厚度及允許偏差應符合下表規定

3.性能要求：

包裝、標志、貯存和運輸：

1、膠帶卷、盤應卷在塑料或紙管芯上，然后裝在塑料袋內，封好袋口再裝入內襯訪潮紙的木箱或干燥潔凈的紙箱內。
2、每一包裝中應附有產品的檢驗合格證，箱體上標明產品名稱、規格批號、毛重、凈重、生產日期、生產廠名稱，及“防潮”“防沖擊”等字樣。
3、該產品從生產之日起貯存期為六個月。超過貯存期按本標準進行檢驗，合格者仍可使用。
4、膠帶應貯存在避光、干燥、潔凈、通風良好的庫房中。
5、膠帶運輸時，應避光、防潮、不得重壓、摔打和機械損傷。

6254-FN Polyimide Film Adhesive Tape F46

Executive Standard: KAPTON*FN insulating film
Standard No: TY6254-FN
Applicable Range: This product is manufactured with the raw material of polyimide film painted with F46 adhesive on single or both sides. After drying, it has been cut into different width. The product can be used for electrical lead winding insulating material. This product is fused at the temperature from 350℃ to 380℃ at 0.5 minute.

1.Technological requirement:
1.1 Appearance:
The tape should be dry, clean and smooth and the tape should have no defects such as air bubble, pinhole, elc.
1.2 Dimension:
1)Length: The length of the tape as well as the number of splice should be made as the requests of client.
2)Width: the width of the tape and its tolerance is as follows: 10mm±0.5mm, 15±0.5mm other width of tape is available too.
3)The tape’s standard thickness and its tolerance is as follows:

1.3.Performance:

2.Packing, marking, storage and transportation
2.1 The film, tape should be rolled on the plastic or paper core. Put it into a plastic bag. After sealing the bag, put them into a wooden or dry paper box. with desiccant in it.
2.2 The test report should be put into the box. Each box should have product’s name, specification, batch number, gross weight, net weight, production date, manufacturer, dampproof as well as impact-proof on it.
2.3 The shelf life is 6 months. It still can be used if the quality is ok after inspection.
2.4 The product should be stored in a lightproof, dry, clean, and ventilated warehouse.
2.5 On transportation, the product should avoid sun light, humidity. The product should not be stressed, breaked and avoid mechanical manage.

****************************************
公司名稱：揚州金冠電氣有限公司
公司地址：江蘇省揚州市寶應經濟開發區
：
傳    真：
客 服  2623069988
微 信 號：JGDQ88888
電子：
聯 系 人：陳
****************************************
詳情請瀏覽：http://www.wjfhcx。。ｃｏｍ
****************************************